Storyboard Camera Move Planner
Plan a pan, tilt, push-in or roll and get the camera view for every frame.
How it works
Describe a 2-D camera move over a storyboard or animation canvas: start and end view centre, zoom and rotation, timing within the shot and a CSS easing. Get the view rectangle for every frame as a table and CSV, a plan drawing and an editable Story Desk board that plays the move in Flipline.
- Frames = round(seconds × FPS), at least 1. Frame 0 shows the start pose and the shot’s last frame the end pose; before the move’s start and after its end the camera holds. Easing uses the same CSS cubic-bezier engine as the Easing Curve tool and Motion Desk.
- Centre and rotation interpolate linearly in eased progress. Zoom interpolates geometrically (equal ratios per frame), so a push-in keeps a steady apparent speed. Zoom 100% shows the whole canvas; the view is canvas size ÷ zoom.
- View left/top/width/height are canvas pixels before rotation; the output is width × height and rotates the artwork by the negative camera roll around the view centre. A frame whose rotated view leaves the canvas shows paper there; such frames are counted.
- The editable Story Desk board uses the same engine: its animatic preview, GIF and video exports draw the board through this camera. It is a 2-D crop-and-roll camera, not 3-D or parallax.
Sources
Part of Flipline
-
Flipline Drawing, storyboards & animation
A few drawings. A little life. Make a flipbook in your browser.
How to use the Storyboard Camera Move Planner
Plan a 2-D pan, tilt, push-in, pull-out or roll over a storyboard canvas and get the camera view for every frame, a plan drawing and an editable Story Desk board.
What it is for
A storyboard often says "slow push in" or "pan left", but an animatic needs to know exactly what the camera sees on each frame. This planner turns such a note into numbers. You describe where the camera looks at the start and at the end (centre, zoom and roll), when the move happens inside the shot and how it eases, and it returns the view rectangle for every frame.
The result fits several workflows: crop and scale a still in a video editor, check whether a framing ever shows the edge of the drawing, or open the shot directly in Flipline's Story Desk, where the same camera engine plays the move in the animatic and in GIF and video exports. It is a flat 2-D camera over one image, without depth or parallax.
Worked example
I planned a push-in towards the upper right third of a 960 × 540 board: centre from 50 % / 50 % to 66 % / 40 %, zoom from 100 % to 200 %, ease-out, over 3 seconds at 24 FPS, with the move finishing at 75 % of the shot.
The tool answered "Camera move planned for 72 frames. The view stays on the canvas."
| Frame | Time (ms) | Centre X | Centre Y | Zoom (%) | View width | View height |
|---|---|---|---|---|---|---|
| 0 | 0 | 480 | 270 | 100 | 960 | 540 |
| 18 | 750 | 555.928 | 243.306 | 140.867 | 681.496 | 383.342 |
| 36 | 1500 | 610.793 | 224.018 | 180.44 | 532.033 | 299.268 |
| 53 | 2208.333 | 633.593 | 216.002 | 199.994 | 480.014 | 270.008 |
| 71 | 2958.333 | 633.6 | 216 | 200 | 480 | 270 |
By frame 53 the camera has practically arrived, and it holds the end framing for the last quarter of the shot. The view at 200 % is exactly half the canvas: 480 × 270 pixels.
A second run that only rolled the camera from 0° to 8° at 100 % zoom warned that 11 of 12 frames show paper beyond the canvas edge. A rotated full-size view always reaches past the corners, so zoom in a little whenever you roll.
How to read the result
- Metrics: frame count, duration, start and end zoom, and how many frames show paper outside the drawing.
- Plan drawing: the canvas with the start view (solid teal), the end view (dashed rust) and one dot per frame on the path of the centre.
- Table: the view at five key frames in canvas pixels. The CSV has every frame, including the top-left corner of the unrotated view and whether it stays inside the canvas.
- Editable Story Desk board: a one-board story with simple staging and this move. Follow the Open in Story Desk link or download the file.
Tips and common mistakes
- Zoom 100 % shows the whole canvas, so a pan at 100 % has nowhere to go. The presets use 125 % for pans and tilts.
- Zoom changes in equal ratios per frame. A push from 100 % to 200 % reaches about 141 % halfway with linear easing, which looks steady on screen.
- Move starts at and Move ends at create holds: 25 % and 100 % wait for the first quarter of the shot.
- A preset other than Custom replaces the start and end fields but still uses your easing and timing.
- Steps are not available for camera moves; use a curve, a keyword or
hold.
FAQ
How does rotation work?
The camera rolls around the view centre; the artwork turns the opposite way in the output, as with a real camera.
Does Story Desk export the move in every format?
The animatic preview, GIF and video follow it. PNG sequences keep the full board artwork and add a camera-moves.json file with the per-frame views.
Can older Flipline versions open a story with a camera move?
No. Such stories are saved as version 2, so an older version refuses them instead of silently dropping the move.
How long can a shot be?
Up to 120 seconds per board at 1–30 FPS.
Guide last updated:
For scripts and AI agents
- JSON API:
POST https://fliplinecameramove.usefulweb.app/api/v1/calculate(same calculation as this page) - Interface description: OpenAPI 3.1 · AI guide: llms.txt
- MCP server (Streamable HTTP):
https://fliplinecameramove.usefulweb.app/mcp· tool nameflipline_camera_move
Example request
curl -s -X POST https://fliplinecameramove.usefulweb.app/api/v1/calculate \
-H 'content-type: application/json' \
-d '{}'